And then ‘F11’ to confirm the install. Wait a few minutes whilst the ESX 3i installer installs 3i on to the SATA hard disk. Once you get the install successful screen press ‘Enter’ to reboot once last time. Upon rebooting your new ESX 3i installation will be up and happily running on your HP Proliant ML110 G5.
- How To Install Mikrotik On Sata Disk
- Install Esxi On Sata Disk Cable Tool
- Install Esxi On Sata Disk Cable Windows 10
There are different ways to install the VMware ESXi 6.5 hypervisor. Today’s post will detail the traditional way of installing ESXi: via CD-ROM or ISO image. We will also walk you through the configuration steps, where the networking part is the most important.
Vladan Seget
Vladan Seget is as an independent consultant, professional blogger, vExpert 2009-2018, VCAP-DCA/DCD, VCP, and MCSA. He has been working for over 20 years as a system engineer.
Latest posts by Vladan Seget (see all)
- VMware VM Hot Add: Changing VM hardware on a running vSphere VM - Fri, Aug 30 2019
- What is the VM Overrides option and how do you use it? - Fri, Aug 16 2019
- VMware DRS tips and tricks - Wed, Aug 7 2019
You might want to know the other methods for installing ESXi 6.5. Where can you install ESXi 6.5 – to the local disk or elsewhere? In fact, there are five different ways to install and deploy VMware ESXi 6.5:
- Installation to a USB stick – the server boots from the USB stick.
- Installation to the local SATA/SAS or FC drive (RAID1)
- Installation to an SD flash card (certain hardware manufacturers provide a mirrored “double” slot)
- Boot from LUN via a hardware iSCSI card, FC or FCoE (fiber channel over Ethernet)
- Stateless booting via VMware auto-deployment
What do you need? Basically, two things:
- A hardware device that is on the VMware hardware compatibility list (HCL)
- An ESXi installation ISO, which you can download from the VMware website, and which you’ll burn to a CD-ROM
Depending on how you’ll connect a storage device to the host, you should have a server with at least two network cards: the first one for the management network and the second one for the storage network. I assume that you’re using either shared storage such as iSCSI storage array or network attached storage (NAS).
Step 1: Installation ^
After you have satisfied both requirements and you’re ready to go, set up your BIOS to boot from CD-ROM. The installer will present you with the following screen to get started:
A love to kill drama. A Love To Kill. The woman is Cha Eun Seok who is a TV talent and movie actor. It was not that she jilted his brother on purpose, but upon a basis of misunderstanding, his hatred toward Cha Eun Seok grows more and more burning. By becoming Cha Eun Seok's private bodyguard, Bok Gu keeps concretely practicing his revenge upon her. Watch A Love to Kill Thailand Drama 2017 Engsub is a Puen grew up in a foster home with his elder brother Mek After a misunderstanding occurs between Mek and his girlfriend Inthira.
The VMware ESXi 6.5 installer
The installer starts automatically within a few seconds.
So far, so good. The next screen says you can install ESXi 6.5 on pretty much everything, but only systems that are on the HCL are supported.
VMware ESXi 6.5 compatibility
How To Install Mikrotik On Sata Disk
Hit Enter and continue with the installation. Accept the end-user license agreement (EULA) and hit the F11 key to continue. The next screen presents you with a choice of destination. Where do you want to install ESXi 6.5?
Make your choice, hit Enter and continue. The next screen will invite you to select a keyboard language and set up a root password. Root is a local account with all privileges; this is a required step. Make sure you pick the right language for your keyboard, as you’ll need to enter a complex password for the account.
Keyboard language and password
Hit the F11 key once again to start the installer. It’ll take just a few minutes to install ESXi 6.5. It is a very lightweight product that needs only a few gb of space.
After a brief moment, you’ll see a screen asking you to eject the installation media and hit Enter to reboot the host. Now you can change the BIOS boot sequence back, though if the boot sequence is CD-ROM > Hard Disk, you’ll be fine.
Remove the installation media
We’re done with the installation. The next step will be configuration.
Step 2: Configuration. ^
Log in to the system first. You’ll need to be at the console.
Next, navigate with the down arrow key to select the “Configure Management Network” menu. Hit Enter to access the menu.
Network configuration
Check the network cards that the installer recognizes. Sometimes when you’re installing on non-certified hardware, the installer may have problems recognizing some network cards, so be aware of that.
Hit Enter to go one level deeper and see the network adapters, VLAN settings and the other network configuration options.
The next submenu allows you to connect or disconnect the network adapters you wish to use.
Connect or disconnect network adapters
Let’s hit the Esc key to go back and configure our network settings.
Hit the Enter key to validate the selection. This will return us to the previous menu, one level higher. Use the arrow key to go down one step and disable the IPv6 configuration completely. Use the up arrow and Space keys to uncheck the selection.
Disable IPv6
Again, validate by hitting the Enter key to go one level higher. Then use the down arrow key again to move to the next menu: domain name server (DNS) configuration.
Quick note: You should create your forward and reverse DNS records on your DNS server before configuring the DNS here.
Hit Enter once more. We’re almost done.
DNS suffixes
Enter any suffixes required for your DNS. You’ll get a prompt to reboot, which will validate the configuration. Note that there is only single reboot necessary! And this is only because we disabled the IPv6 configuration. This means that if you left the IPv6 in place, you wouldn’t need to reboot ESXi 6.5, not even once.
Step 3: Connect to the host ^
We can connect to a single host two ways:
- Via a traditional Windows C++ client (you’ll need to install it on your Windows workstation)
- Via an HTML 5 web-based browser (no software to install)
I’m sure everyone’s familiar with the traditional Windows client, so let me show you the connection via an HTML5 web-based browser.
The URL to remember is:
https://fqdn_of_your_ESXi/ui
or
https://IP_of_your_ESXi/ui
ESXi web client
Well, this is it. We have successfully configured our ESXi 6.5 hypervisor. You can start creating VMs on local storage or wait for one of our future posts where we’ll be configuring shared storage (iSCSI or NFS).
In my next post I will explain how to deploy VMware vCenter (VCSA) 6.5
- How to install and configure an ESXi 6.5 host
Users who have LIKED this post:
Install VM running ESXi on an ESXi host
vSphere was released in 2009, with the 4.1 incremental release arriving in July of 2010. As with prior versions, ESXi (as well as ESX) is VMware's hypervisor that is the critical piece vSphere. For anyone wanting to experiment with vSphere features, work with testing updates, or set up a lab environment to practice for training purposes; a virtualized lab environment can be very valuable.ESXi can be installed as a guest operating system for these and other non-production purposes. In this gallery, the steps required to install virtual machine running ESXi will be performed on an ESXi host. While this is a capable function of the platform, it is not supported and should not be used for production workloads.